The KNX-USB interface enables communication between the KNX bus and a computer for programming and monitoring devices on the bus by using the ETS program. Additionally, the interface can work in the bus logging mode, in which the history of events generated on the KNX bus is saved to the interface non-volatile memory (up to 350 000 events).
In the bus logging mode, the interface does not support communication with the ETS program.
Features:
communication with the KNX bus via integrated bus connector
power supply from the KNX bus or from the computer USB port
galvanic isolation of the KNX system and computer
data transmission between the interface and the computer acc. to USB 2.0 standard
LEDs indicating the device status
The KNX-PS640 power supply unit enables the KNX bus to be supplied with system voltage (SELV). The output with integrated choke makes it possible to separate the power supply from the KNX bus communication line.
Features:
wide input voltage range: 195…265 V AC (50/60 Hz)
output voltage for the bus: 28…30 V DC
short-circuit protection for AC power input
short-circuit and overload protection for DC power output
LED indicators of power supply operating status
installation in electrical cabinets, on DIN rail (35 mm)
The KNX-SA41 module is a universal switch actuator, which makes it possible to control electrical devices (lighting, ventilation). The telegrams received from various KNX devices (e.g. sensors) are converted, via the module, into concrete actions, such as switching on/off light or fan.
The KNX-SA41 module has 4 relay outputs. Each of them corresponds to one logical channel.
Features:
communication with KNX bus via integrated bus connector
feedback on the state of module and individual channels
reaction of each channel can be defined in case of KNX bus voltage loss and recovery
reaction of each channel can be defined in case of mains voltage recovery
time functions (flashing, on/off delay, staircase light function with advance warning option and operating time change)
logic functions (AND, NAND, OR, NOR, XOR, XNOR)
threshold value function
safety functions
state forcing functions
scenes for each of the channels can be called up by using 1- and 8-bit commands
manual control of each channel state by using buttons situated on enclosure
status LEDs for each channel
capability of switching between resistive, inductive and capacitive loads
module configuration using ETS software
KNX-SA24 module is a universal switch actuator, which makes it possible to control electrical devices (lighting, ventilation). The telegrams received from various KNX devices (e.g. sensors) are converted, via the module, into concrete actions, such as switching on/off light or fan.
The KNX-SA24 module has 8 relay outputs. Each of them corresponds to one logical channel.
Features:
communication with KNX bus via integrated bus connector
feedback on the state of module and individual channels
reaction of each channel can be defined in case of KNX bus voltage loss and recovery
reaction of each channel can be defined in case of mains voltage recovery
time functions (flashing, on/off delay, staircase light function with advance warning option and operating time change)
logic functions (AND, NAND, OR, NOR, XOR, XNOR)
threshold value function
safety functions
state forcing functions
scenes for each of the channels can be called up by using 1- and 8-bit commands
manual control of each channel state by using buttons situated on enclosure
status LEDs for each channel
capability of switching between resistive, inductive and capacitive loads
module configuration using ETS software
suitable for mounting on DIN rail (35 mm)
The KNX-DIM21 module is a universal two-channel dimming KNX actuator that allows stepless control of light sources up to 300 W per channel. The light can be turned on / off, dimmed down (darker) / dimmed up (brighter), set by using a predefined scene or another function via the KNX bus. The actuator can be used with resistive, inductive and capacitive loads (R, L, C).
The module is designed for use with 230 V AC voltage
Features:
communication with KNX bus via integrated bus connector
automatic recognition of the connected load type
adjustable lighting characteristic to suit the load type
two-stage, firmware-hardware overheating protection system
overload protection
feedback on status of module and individual channels
definable reaction of each channel in case of KNX voltage loss and recovery
definable reaction of each channel in case of voltage recovery
time functions (switching delay, staircase function with warning option and operating time change)
value forcing function
option to call scenes for each channel by using 1- and 8-bit commands
manual operation of each channel status by using buttons on the enclosure
LEDs to indicate each channel status and signal troubles
module configuration using ETS software
suitable for mounting on DIN rail (35 mm)
The KNX-BSA12L is a KNX blind/shutter actuator that allows you to control the movement of sun protection products such as horizontal (Venetian) blinds, vertical blinds, roller shutters and awnings. It also enables control of the movement of electrically-operated windows. The KNX-BSA12L module is designed to control devices having the 24 V DC motor. The module has 2 physical outputs with two corresponding logic channels. Each channel allows control of one selected type of blind/shutter or window.
Features:
communication with the KNX bus via integrated bus connector
feedback information about the state of module and individual channels
selectable type of blind/shutter for each channel
automatic detection of blind/shutter travel time and slat adjustment time
weather alarms (rain, wind, frost)
position forcing function
ability to call scenes for each channel by using 1- and 8-bit commands
detection of blind/shutter errors (no power, incorrect position, mechanical jam, motor overheating)
manual control of blind/shutter travel by using buttons on the enclosure
LEDs to indicate status of each channel/blind/shutter
module configuration using ETS program
KNX-BIN24 is a universal module of KNX binary inputs that enables electrical (voltage) signals to be converted into control telegrams for otherKNX-BSA12H is a KNX blind/shutter actuator that allows you to control the movement of sun protection products such as horizontal (Venetian) blinds, roller shutters and awnings. It also enables control of the movement of electrically-operated windows. The KNX-BSA12H module is designed to control devices having the 230 V AC motor. The module has 2 physical outputs with two corresponding logic channels. Each channel allows control of one selected type of blind/shutter or window.
Features:
communication with the KNX bus via integrated bus connector
feedback information about the state of module and individual channels
selectable type of blind/shutter for each channel
automatic detection of blind/shutter travel time and slat adjustment time
weather alarms (rain, wind, frost)
position forcing function
ability to call scenes for each channel by using 1- and 8-bit commands
detection of blind/shutter errors (no power, incorrect position, mechanical jam, motor overheating)
manual control of blind/shutter travel by using buttons on the enclosure
LEDs to indicate status of each channel/blind/shutter
module configuration using ETS program
suitable for mounting on DIN rail (35 mm)
KNX-BIN24 is a universal module of KNX binary inputs that enables electrical (voltage) signals to be converted into control telegrams for other devices on the bus. These signals may be generated by conventional ON/OFF buttons (to operate lighting, etc.) or by potential-free contacts of devices such as reed switches or sensors of various types of physical quantities.
The module has 8 physical inputs which allow it to handle 8 independent signals ranging from 0 to 30 V DC and AC.
Features:
communication with the KNX bus via integrated bus connector
definable channel polarity (NO / NC)
configurable time of short / long button press
virtual channels for receiving 1-bit telegrams from other KNX bus devices
virtual logic channels for creating logical links between module channels
virtual timer channels for creating time links
possibility to define 20 function blocks that perform one of the available functions:
switch / value transmitter
edge response
dimmer
shutter controller
switching sequence
counter
scene controller
possibility to control each function block using any channel
control of several function blocks using one channel
control of lighting and shutters using 1 or 2 buttons (channels)
ability to call a scene from any channel by using 8-bit commands
manual operation of physical channels status by using buttons on the enclosure
LEDs to indicate status of physical channels
module configuration using ETS program
suitable for mounting on DIN rail (35 mm)